MN Blue Flame   Natural Gas: Solving tomorrow's problems today



Facts About Insulation and Ventilation Download this document for printing

Types of Insulation | Where to Install | Bypasses | Ice Dam Formation | Sealing Bypasses | Vapor Barriers | Ventilation | Crawl Spaces

Insulation Saves Two Ways

Almost every homeowner can save both energy and money by adding insulation. Good insulation is permanent, maintenance-free, and can return your investment by lowering your fuel bills. The payback period varies with type of insulation materials, purchase and installation costs, and the price of fuel.

The basic function of insulation is to resist the flow of heat. This is expressed as an "R" value; the higher the "R" value, the more resistance to heat flow. Insulation materials have different "R" values, so buy insulation according to the "R" value you wish to attain, not by total inches.


Types of Insulation Return to top

There are several types of insulation with various "R" values and prices. Some are easy to install yourself; others may require a contractor or special equipment.

Insulating material "R" value per inch
Batt & Blanket  
  Mineral wool R—3.15 to 3.85
  Fiberglass R—3.15 to 3.85
Loose Fill (Pour in)  
  Mineral Wool R—2.88 to 3.31
  Fiberglass R—2.88 to 3.31
  Cellulose Fiber R—3.70
  Vermiculite (Expanded) R—2.13 to 2.27
  Perlite (Expanded) R—2.70
Rigid Insulation  
  Expanded Polystyrene Extruded Plain (Styrofoam) T.M. R—5.00
  Expanded Polystyrene (Beadboard) R—3.57
  Expanded Polyurethane (Foam) R—6.25
  Fiberglass (rigid board) R—5.00

NOTE: To assure fire safety, rigid insulation should be covered with 1/2" gypsum wallboard when installed.

No matter what kind of insulation you buy, be sure it meets federal standards for fire and vermin resistance. Check for approval codes listed on the packaging.


Where to Install Return to top

The list below tells you which places in your home need insulation. An unconditioned space is an area with no heat or air conditioning; a conditioned space is heated in winter and air conditioned in summer.

Where to insulate a home How much
1. Ceilings with unconditioned spaces above R—38 to 44
2. "Knee" walls of a finished or conditioned attic Between studs
R—11
3. Exterior walls or walls between conditioned and unconditioned spaces R—19
(New Constr.)
4. Floors over unconditioned or outside spaces R—19
5. Perimeter of a concrete floor slab close to grade level High R
sheathing on the outside
6. Walls of finished or conditioned basement R—11 to R—13
7. Top of foundation or basement wall. (Rim joist or band joist) Fill with fiberglass batts
8. Sloping rafters—Leave an air space for ventilation between the insulation and the roof deck. Select insulation thickness accordingly. R—11 (2" x 4")
R—19 (2" x 6")

And don’t forget…

  • Add insulation to your attic door.
  • Wrap insulation around heating and air conditioning ducts which pass through unconditioned spaces.
  • Wrap hot water pipes with insulated pipe wrap.
  • Add insulation to foundation wall.
  • Seal bypass areas.

Installing insulation

  • Do not block soffit vents with insulation.
  • Provide a 3-inch clearance around heat-producing fixtures such as recessed ceiling lights.
  • Watch for nails that stick through the roof sheathing above your head.
  • Wear work gloves, loose-fitting clothing and a long-sleeved shirt to avoid skin irritation; wear a mask to prevent inhaling insulation particles.

Bypasses Return to top

Besides insulating, caulking and weatherstripping, a very important step in weatherizing your home is finding and sealing bypasses.

A bypass is any hole, crack or crevice that allows conditioned air to leak through your home’s insulation. Bypasses are found in interior and exterior walls, around vent pipes, recessed light fixtures, plumbing and electrical wire passages, and chimneys. Seal bypasses before insulating; if your attic is already insulated or floored, you may have to remove insulation or floor boards to plug the bypasses. If bypasses are not sealed the insulation only "filters" the warm air on its way to the attic, and your roof will still be warm, and will possibly develop ice dams.


Ice Dam Formation Return to top

Ice dams form when heat enters an attic and melts snow on the roof. This melted snow (water) runs down the roof, under the blanket of snow, to the edge of the roof where colder conditions cause it to freeze, forming ice dams. If ice dams are not removed, water may be caught behind them, forced under shingles or spill over to form icicles. This can result in costly damage to your home: wet (ineffective) insulation; stained or cracked plaster or sheet rock; damp, rotting walls; and stained, blistered or peeling paint.

Preventing ice dams

Since the basic cause of ice dams is a warm roof, the solution is to maintain a cold roof. You can take three steps to achieve a cold roof:

  • Seal bypasses
  • Insulate
  • Ventilate

Notes:

  • Seal around your chimney with non-galvanized steel and silicone caulk.
  • Do not plug or seal any hole within 3 inches of a recessed light fixture. If you can, remove the fixture completely and replace with conventional lighting.
  • Do not plug vents or fresh air intakes, but be sure these do not leak around the edges and joints.

Temporary or emergency measures

If you already have water or ice dam problems, you need to take remedial action. The following methods are sometimes successful but will probably have to be repeated with every winter storm.

  • Remove snow with a roof rake. Beware of icy conditions and falling snow and ice.
  • Hose off ice dams with tap water on a warm day. However, water run-off from hosing could damage shrubbery.
  • Steam the roof. Steam could cause expansion and contraction of the roof deck.
  • Install electric cables along the eaves and in the valleys of the roof. Melting is limited to a few inches near the cables, and the sawtooth melting often causes secondary ice dams to develop higher on the roof. Also, cables use a great deal of energy.
  • Do not chop ice off the shingles or use a blow torch; this could damage the roof.

Remember, these are only temporary or emergency measures. The most effective way to prevent ice dams is by sealing bypasses, properly insulating the attic floor, and adequately ventilating the roof area.

Sealing Bypasses Return to top

Techniques for sealing bypasses depend on the size and accessibility of the openings. Regular caulk can be used for small holes. Holes too large or deep for regular caulk can be sealed with foam caulk or void filler. Open wall cavities and other large openings can be sealed with pieces of rigid material cut to fit and caulked into place, or stuffed with lightly rolled unfaced fiberglass insulation.


Vapor Barriers Return to top

Humidity and moisture that collect in insulated areas can cause problems. Therefore, vapor barriers should be placed between insulation and the conditioned space. Suitable vapor barriers can be found on some blanket insulations. Where no vapor barrier is attached, a separate vapor barrier made of the following materials works well:

  • Polyethylene film
  • Paper-backed aluminum
  • Laminated papers consisting of a continuous sheet of asphalt between two sheets of paper
  • Surface-coated, asphalt-saturated building paper

Notes on Vapor Barriers

  • Do not add vapor barrier-faced insulation over existing insulation. If unfaced bolts are not available, slash or strip vapor barrier from batts before installing.
  • Replace vapor barriers damaged during installation or repair with mending tape.
  • In existing houses where vapor barriers are impossible to install, moisture protection may be obtained by painting interior walls and ceilings with vapor-resistant paint. Follow manufacturer’s instructions for applications.

Ventilation Return to top

Vents are openings in the attic area that allow moisture to escape. If you don’t ventilate properly, water vapor can condense and collect on insulation and rafters. This will reduce the effectiveness of the insulation and could damage the house. Also, without ventilation, attic heat could penetrate into living areas during summer.

Where and how much

How much ventilation you need is determined by the area of your attic; normally one square foot of vent is needed for every 300 square feet of attic area. If you do not have a vapor barrier in this area, the amount of ventilation could be doubled (up to one square foot of vent for every 150 square feet of attic area). Keep in mind that screens and louvers on vents reduce venting capacity, so openings must be increased proportionately. Use a combination of vents, half located low on the roof and half higher up, so air can flow in one and out the other. For example, use soffit and ridge vents. Install baffle boards as necessary to prevent insulation from blocking air flow. Keep vent screens clean.

Power ventilation

Natural ventilation is usually sufficient. Using electrically powered vents is optional. Power vents require additional attic ventilators and they may interfere with proper furnace and fireplace venting. Be sure you choose the correct size power vent to handle the area.


Crawl Spaces Return to top

Unconditioned crawl space

Crawl spaces require insulation, ventilation and vapor barriers. In unconditioned crawl spaces one vapor barrier covers the ground and another covers the area between the insulation and subfloor. The insulation is installed between the floor joists. (Refer to illustration.)

Conditioned crawl space

If a conditioned crawl space is desired, a vapor barrier covers the ground in the same way as in the unconditioned crawl space. Insulation is applied to the rim joist, down the wall and onto the floor, so a vapor barrier should also be installed to cover the insulation. (Refer to illustration.) In all cases, be sure to insulate water and drain pipes and heat ducts in the crawl space.

Foundation vent

If the crawl space opens into a conditioned basement or cellar it should be ventilated to the outside (one square foot of vent for every 1,500 square feet of floor area) with vents placed on opposite walls for cross ventilation. These foundation vents can be closed and sealed in winter and opened in warm weather.

Call your local natural gas utility company or the Minnesota Blue Flame Gas Association at (763) 424-1841.